 |
 |
 FAQ Forum Help Official CCS Support  Search
 Register
 Profile  Log in to check your private messages  Log in
|
CCS does not monitor this forum on a regular basis. Please do not post bug reports on this forum. Send them to CCS Technical Support |
| Search found 10 matches |
| Author | Message |
|---|---|
 Topic: baud rate out of range |
|
| Shishido Replies: 8 Views: 16639 |
 Forum: General CCS C Discussion Posted: Tue Apr 28, 2015 7:47 am Subject: Sorry for jump in |
| Hello, I succeeded compile as below.
#include <24FJ128GA010.h> #FUSES XT,PR_PLL,NOPROTECT,NOJTAG,NOWDT,NOCKSFSM #use delay(clock=32M) #PIN_SELECT U1TX = PIN_B5 // ... |
|
| Topic: SPI pin assign |
|
| Shishido Replies: 3 Views: 8304 |
Forum: General CCS C Discussion Posted: Sun Apr 26, 2015 7:21 am Subject: Thank you very much |
| Thank you very much, I will try it.
BTW, have you experienced Dual SPI or Quad SPI mode used by PIC? – Dual SPI: CLK, /CS, IO0, IO1 – Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3 You don't... ... |
|
| Topic: SPI pin assign |
|
| Shishido Replies: 3 Views: 8304 |
Forum: General CCS C Discussion Posted: Fri Apr 24, 2015 3:04 am Subject: SPI pin assign |
| Currently, I am using PIC18F27J53 for SPI memory module according with data sheet
http://ww1.microchip.com/downloads/en/DeviceDoc/39964B.pdf #define EEPROM_SELECT PIN_A2 // CS #define EEPROM ... |
|
| Topic: Copy data from SPI Flash ROM W25Q64C |
|
| Shishido Replies: 5 Views: 16302 |
Forum: General CCS C Discussion Posted: Fri Apr 24, 2015 2:17 am Subject: Done COPY SPI memory tool |
| Many Thanks , I done SPI memory copy tool .
Pic micom :PIC18F27J53 , clock 20M When copy 64Mbit memory. the time is 6:30 sec include verify. Since I hope speed up copy time. I will challenge ... |
|
| Topic: #use capture can be 2 channels? |
|
| Shishido Replies: 6 Views: 9293 |
Forum: General CCS C Discussion Posted: Sat Apr 11, 2015 7:17 am Subject: Resolves |
| hmm...
define=capture_ticks_per_second compiler doesn't 'like' this. Check the PIC header to see what options for DEFINE are valid. Jay /////////////////////////////////// Thank you v ... |
|
| Topic: #use capture can be 2 channels? |
|
| Shishido Replies: 6 Views: 9293 |
Forum: General CCS C Discussion Posted: Sat Apr 11, 2015 2:43 am Subject: #use capture can be 2 channels? |
| without having any background using your chip:
#use capture(CCP1, FASTEST, CAPTURE_RISING, timer=1, define=capture_ticks_per_second, fastest, stream=CCP1_STREAM) #use capture(CCP2, ... |
|
| Topic: #use capture can be 2 channels? |
|
| Shishido Replies: 6 Views: 9293 |
Forum: General CCS C Discussion Posted: Fri Apr 10, 2015 10:31 pm Subject: Thanks |
| >As with just about any #use, there is a "stream" option. >Make two different #use capture() directives and assign them different >streams. Then supply the stream arguments for ca ... | |
| Topic: #use capture can be 2 channels? |
|
| Shishido Replies: 6 Views: 9293 |
Forum: General CCS C Discussion Posted: Fri Apr 10, 2015 5:10 pm Subject: #use capture can be 2 channels? |
| I want to measure capture time by 2 channels such as CCP1 and CCP2.
However, it seems to #include <16f1938.h> #DEVICE ADC=10 #fuses INTRC_IO,NOWDT,NOPROTECT,PUT,NOCPD,NOLVP,BROWNOUT, ... |
|
| Topic: Copy data from SPI Flash ROM W25Q64C |
|
| Shishido Replies: 5 Views: 16302 |
Forum: General CCS C Discussion Posted: Thu Feb 26, 2015 3:15 am Subject: Thanks Jay san |
| Dear Jay san, thank you for your good comments.
Actually, I have experienced developed I2C protocol device such as EEPROM ,I2C LCD ,etc controlled by PIC16,PIC18. According datasheet of Winbond W ... |
|
| Topic: Copy data from SPI Flash ROM W25Q64C |
|
| Shishido Replies: 5 Views: 16302 |
Forum: General CCS C Discussion Posted: Wed Feb 25, 2015 7:51 pm Subject: Copy data from SPI Flash ROM W25Q64C |
| Dear All, I would like to copy to new blank Flash W25Q64CROM data of BIOS flash ROM (Winbond W25Q64C )
which protocol is SPI by PIC18 or PIC 24. we can get datasheet http://www.alldatasheet. ... |
|
All times are GMT - 6 Hours |
Powered by phpBB © 2001, 2005 phpBB Group