 |
 |
 FAQ Forum Help Official CCS Support  Search
 Register
 Profile  Log in to check your private messages  Log in
|
CCS does not monitor this forum on a regular basis. Please do not post bug reports on this forum. Send them to CCS Technical Support |
| Search found 8 matches |
| Author | Message |
|---|---|
 Topic: Max232 Problem |
|
| Whizzard9992 Replies: 10 Views: 25246 |
 Forum: General CCS C Discussion Posted: Tue Apr 27, 2004 9:53 am Subject: Max232 Problem |
| Excellent Information. Thank you. | |
| Topic: Max232 Problem |
|
| Whizzard9992 Replies: 10 Views: 25246 |
Forum: General CCS C Discussion Posted: Mon Apr 26, 2004 9:55 am Subject: Thanks |
| Thank you both for your help.
The reason I inquired about the Max232 here is because I wasn't sure if it was a voltage or input issue related to the PIC. I figured I probably wasn't the only person ... |
|
| Topic: Max232 Problem |
|
| Whizzard9992 Replies: 10 Views: 25246 |
Forum: General CCS C Discussion Posted: Fri Apr 23, 2004 3:32 pm Subject: Max232 Problem |
| I have a PIC16F627A hooked to an LED bargraph on a 5V regulated power supply. All Max232 pins are floating except the cap pins, vcc, cng, pins 8 and 9. Pin 9 is going to an input on the PIC.
From t ... |
|
| Topic: Max232 Problem |
|
| Whizzard9992 Replies: 10 Views: 25246 |
Forum: General CCS C Discussion Posted: Fri Apr 23, 2004 12:16 pm Subject: Max232 Problem |
| Ok. That did solve one problem. I removed the pull-up, though I didn't replace it with a pull-down because you said that there was one internally. I'm getting a 4-second delay before I get the signal ... | |
| Topic: Max232 Problem |
|
| Whizzard9992 Replies: 10 Views: 25246 |
Forum: General CCS C Discussion Posted: Thu Apr 22, 2004 6:46 pm Subject: Max232 Problem |
| I have a Max232 chip hooked to a modem and a PIC16F627A. I Have common ground on the Serial Port and CS hooked to Pin 8 on the Max232.
My problem is that when the modem is turned off, after about 3 ... |
|
| Topic: Newbie Question |
|
| Whizzard9992 Replies: 7 Views: 16001 |
Forum: General CCS C Discussion Posted: Wed Apr 14, 2004 11:28 am Subject: Newbie Question |
| Excellent information. This helped a TON.
Thanks! |
|
| Topic: Newbie Question |
|
| Whizzard9992 Replies: 7 Views: 16001 |
Forum: General CCS C Discussion Posted: Wed Apr 14, 2004 8:45 am Subject: Awesome |
| Thank you all for your input!!!!
I'm a veteran programmer but new to MCUs. I have a book and am drudging my way through it, so please bear with me if my knowledge is like swiss cheese. I did ge ... |
|
| Topic: Newbie Question |
|
| Whizzard9992 Replies: 7 Views: 16001 |
Forum: General CCS C Discussion Posted: Tue Apr 13, 2004 4:50 pm Subject: Newbie Question |
| I'm using a PIC16F627A, and I can't get a signal from any pin. Any help would be greatly appreciated. Here's my code. I don't have any I/O pins grounded: only A7 hooked to an LED/RESISTOR.
I have V ... |
|
All times are GMT - 6 Hours |
Powered by phpBB © 2001, 2005 phpBB Group