 |
 |
 FAQ Forum Help Official CCS Support  Search
 Register
 Profile  Log in to check your private messages  Log in
|
CCS does not monitor this forum on a regular basis. Please do not post bug reports on this forum. Send them to CCS Technical Support |
| Search found 9 matches |
| Author | Message |
|---|---|
 Topic: Bought Book and e3 combo but USB driver wont work - Help! |
|
| fos Replies: 8 Views: 14111 |
 Forum: General CCS C Discussion Posted: Tue Dec 23, 2014 11:36 am Subject: Bought Book and e3 combo but USB driver wont work - Help! |
| Arizona Chris,
I was in the same boat a couple of weeks ago. I started with the install based upon the appendix. The E3 USB loader information isn't even apparent in the text when you set up the fi ... |
|
| Topic: Bought Book and e3 combo but USB driver wont work - Help! |
|
| fos Replies: 8 Views: 14111 |
Forum: General CCS C Discussion Posted: Tue Dec 23, 2014 3:00 am Subject: Bought Book and e3 combo but USB driver wont work - Help! |
| Select the Compile tab on the top menu.
There is a down arrow on the right side of the Build & Run box. Select the little down arrow ribbon on the right side of the box. In the pulled down ... |
|
| Topic: Embedded C Programming Book |
|
| fos Replies: 13 Views: 20994 |
Forum: General CCS C Discussion Posted: Fri Dec 05, 2014 2:50 am Subject: Embedded C Programming Book |
| Well, I now have the answer but it occurs to me that a forum populated with helpful individuals like yourself, has very little value.
For the answers, see Newnes website for the text. Thanks for ... |
|
| Topic: Embedded C Programming Book |
|
| fos Replies: 13 Views: 20994 |
Forum: General CCS C Discussion Posted: Thu Dec 04, 2014 12:29 pm Subject: Embedded C Programming Book |
| Does anyone know if the correct answers for the end of chapter questions are available?
Thanks, Jeff |
|
| Topic: Robotics Development Kit |
|
| fos Replies: 5 Views: 6311 |
Forum: General CCS C Discussion Posted: Tue Jun 30, 2009 11:05 am Subject: Robotics Development Kit |
| The CCS Robotics kit is derived from the Portland robot that can be found at:
http://www.junun.org The motherboard on the CCS robot has more standard features than the Portland version. Be su ... |
|
| Topic: CCS Robotics - Servo Calibration ? |
|
| fos Replies: 3 Views: 4771 |
Forum: General CCS C Discussion Posted: Wed Jun 24, 2009 4:40 pm Subject: CCS Robotics - Servo Calibration ? |
| If anyone else is having the same problem with their CCS Robotics Development kit, http://www.junun.org sells the pre-modified servos for $16 each.
Jeff PS. I did contact CCS support via email. ... |
|
| Topic: CCS Robotics - Servo Calibration ? |
|
| fos Replies: 3 Views: 4771 |
Forum: General CCS C Discussion Posted: Wed Jun 24, 2009 3:11 pm Subject: CCS Robotics - Servo Calibration ? |
| I found this info on the junan.com site after a lot of digging...
Using a razor or coping saw, cut a 1mm groove in the end of the potentiometer shaft. This will be used as screwdriver slot when the ... |
|
| Topic: CCS Robotics - Servo Calibration ? |
|
| fos Replies: 3 Views: 4771 |
Forum: General CCS C Discussion Posted: Wed Jun 24, 2009 11:06 am Subject: CCS Robotics - Servo Calibration ? |
| Please reference Chapter 6 Basic Movement in the exercise manual that accompanies the Robotic Development Kit - manual version - April 2009
See paragraph below gray source code box: Quote: Compi ... |
|
| Topic: Tutorial to learn CCS PIC 'C'........ |
|
| fos Replies: 4 Views: 16543 |
Forum: General CCS C Discussion Posted: Mon Jun 01, 2009 9:40 am Subject: Tutorial to learn CCS PIC 'C'........ |
| Benson is a good writer. It helps to have his earlier books as a reference. For example Easy Picn and Picn Up the Pace.
Jeff |
|
All times are GMT - 6 Hours |
Powered by phpBB © 2001, 2005 phpBB Group