CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support

Search found 11 matches
CCS Forum Index
Author Message
  Topic: ccsload: code not protected problem.
jai

Replies: 5
Views: 6861

PostForum: General CCS C Discussion   Posted: Fri Jun 07, 2013 6:44 am   Subject: ccsload: code not protected problem.
Dear Ttelmah,

Thank you for the info.

I think i should clarify the problem.

I understand that if not protected the verification must be chip = file.
and if protected chip not equal to file. ...
  Topic: ccsload: code not protected problem.
jai

Replies: 5
Views: 6861

PostForum: General CCS C Discussion   Posted: Fri Jun 07, 2013 12:42 am   Subject: ccsload: code not protected problem.
Hi all,

Yes i would like to confirm that there is a error in
CCSLOAD Programmer Control Software for Windows - 4.040 and 4.039

I tried v4.025 there is no error in that version.
It displays co ...
  Topic: ccsload: code not protected problem.
jai

Replies: 5
Views: 6861

PostForum: General CCS C Discussion   Posted: Fri Jun 07, 2013 12:18 am   Subject: ccsload: code not protected problem.
Dear PCM programmer,

Thanks for the reply.

I am not on debug mode.

I also found that if i program without code protect and make a chip = file verify
there is a 100% match.

But when i set ...
  Topic: ccsload: code not protected problem.
jai

Replies: 5
Views: 6861

PostForum: General CCS C Discussion   Posted: Thu Jun 06, 2013 7:46 am   Subject: ccsload: code not protected problem.
Hi all,

I am programming the 16F887 with the fuses

#FUSES NOWDT
#FUSES HS
#FUSES NOBROWNOUT
#FUSES NOLVP
#FUSES MCLR
#FUSES PROTECT

Also tried with this
#FUSES W ...
  Topic: 16x2 LCD powerup question.
jai

Replies: 4
Views: 5605

PostForum: General CCS C Discussion   Posted: Fri Jul 01, 2011 12:28 am   Subject: 16x2 LCD powerup question.
Thanks for the input.

regards,
jai.
  Topic: 16x2 LCD powerup question.
jai

Replies: 4
Views: 5605

PostForum: General CCS C Discussion   Posted: Thu Jun 30, 2011 7:20 am   Subject: 16x2 LCD powerup question.
I found that the VEE voltage was 0 Volt.
When i increase the voltage to greater than 0.5 Volt.
Some of the characters do not properly appear.

Regards
Jai
  Topic: 16x2 LCD powerup question.
jai

Replies: 4
Views: 5605

PostForum: General CCS C Discussion   Posted: Thu Jun 30, 2011 7:09 am   Subject: 16x2 LCD powerup question.
Hi All,

I am working on a project where the display is JHD-162A. Which is a 16x2 line LCD module.
It works fine. The problem is when i turn power on first it displays black box on one line. After ...
  Topic: Is this the best speed possible in this configuration?
jai

Replies: 7
Views: 7688

PostForum: General CCS C Discussion   Posted: Thu Apr 14, 2011 3:29 am   Subject: Is this the best speed possible in this configuration?
I was using Delphi for programming as the PC side software. When you start
the program by itself and not in the IDE. It takes about 1 min 10 seconds to
complete. I wonder whether more speed can be ...
  Topic: Is this the best speed possible in this configuration?
jai

Replies: 7
Views: 7688

PostForum: General CCS C Discussion   Posted: Tue Apr 12, 2011 6:29 am   Subject: Is this the best speed possible in this configuration?
Even the universal programmer GALEP4 takes about 2 min to program the whole chip.
  Topic: Is this the best speed possible in this configuration?
jai

Replies: 7
Views: 7688

PostForum: General CCS C Discussion   Posted: Tue Apr 12, 2011 6:27 am   Subject: Is this the best speed possible in this configuration?
Sorry if my posting in unclear. It takes 7 minutes to program the full EEPROM chip.
  Topic: Is this the best speed possible in this configuration?
jai

Replies: 7
Views: 7688

PostForum: General CCS C Discussion   Posted: Tue Apr 12, 2011 5:59 am   Subject: Is this the best speed possible in this configuration?
Hi All,

I am working on a application where a 18F2550 is configured as CDC usb.
I am transferring data from computer to ext EEPROM.
I am using 24LC512 eeprom. Working on page mode(128 bytes).
It ...
 
Page 1 of 1
All times are GMT - 6 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group