 |
 |
 FAQ Forum Help Official CCS Support  Search
 Register
 Profile  Log in to check your private messages  Log in
|
CCS does not monitor this forum on a regular basis. Please do not post bug reports on this forum. Send them to CCS Technical Support |
| Search found 8 matches |
| Author | Message |
|---|---|
 Topic: Calling bootloader from application |
|
| raffaele Replies: 3 Views: 10323 |
 Forum: General CCS C Discussion Posted: Mon May 01, 2017 6:35 am Subject: Calling bootloader from application |
| Thank you very much, I wrote here because it didn't seem to me that reset_cpu was launching bootloader and I'm newbie with bootloader.
Anyway now I'm finishing to write everthing, I've put flag, CRC3 ... |
|
| Topic: Calling bootloader from application |
|
| raffaele Replies: 3 Views: 10323 |
Forum: General CCS C Discussion Posted: Mon May 01, 2017 3:41 am Subject: Calling bootloader from application |
| Hi,
I'm starting using bootloader on PIC24FJ128GA306. I've used the CCS serial bootloader and it works, now I'm adding the option to load from external flash. Application download the new firmware o ... |
|
| Topic: UART problem on PIC24 |
|
| raffaele Replies: 6 Views: 9533 |
Forum: General CCS C Discussion Posted: Fri Feb 26, 2010 5:01 am Subject: UART problem on PIC24 |
| Thank you, it's working connected a 3.3V serial device, thank you for your advice. | |
| Topic: UART problem on PIC24 |
|
| raffaele Replies: 6 Views: 9533 |
Forum: General CCS C Discussion Posted: Thu Feb 25, 2010 3:12 am Subject: UART problem on PIC24 |
| Usually RX pin are at high voltage level and driven low by TX pin, to confirm this i've checked the RX pin of HW UART of a PIC16F689 leaving it disconnected.
I've tried also to set the inverting bit ... |
|
| Topic: UART problem on PIC24 |
|
| raffaele Replies: 6 Views: 9533 |
Forum: General CCS C Discussion Posted: Wed Feb 24, 2010 6:31 am Subject: UART problem on PIC24 |
| I had a Max3223 to connect PIC to PC and I noticed no received data on PIC. Then I've disconnected MAx3223 leaving free the pin, with scope I can see 0V. 0V means 1 logic with TTL UART. | |
| Topic: UART problem on PIC24 |
|
| raffaele Replies: 6 Views: 9533 |
Forum: General CCS C Discussion Posted: Wed Feb 24, 2010 5:36 am Subject: UART problem on PIC24 |
| Hello,
I'm having problem receiving data with PIC24HJ64GP502, comp. v4.093. I found that the RX pin is always at 0V in idle mode, and not at 3.3V. The problem is on both UART, while no poblem to ... |
|
| Topic: Starting PIC18 and PIC24 |
|
| raffaele Replies: 2 Views: 4262 |
Forum: General CCS C Discussion Posted: Wed Feb 24, 2010 3:25 am Subject: Starting PIC18 and PIC24 |
| Thank you, it works. I found also PIC24 Wizard is good to configure fuses. | |
| Topic: Starting PIC18 and PIC24 |
|
| raffaele Replies: 2 Views: 4262 |
Forum: General CCS C Discussion Posted: Fri Feb 19, 2010 4:54 am Subject: Starting PIC18 and PIC24 |
| Hello to all,
I'm starting using PIC18 and PIC24 family with PCWHD 4.093. I have few PIC like 24HJ64GP502, 18F25J11, 24HJ128GP502. I wrote a simple code for blinking a led but it's not working. ... |
|
All times are GMT - 6 Hours |
Powered by phpBB © 2001, 2005 phpBB Group