CCS :: View topic - Software Uart and External Interrupt issue

FAQ

Forum Help

Official CCS Support

Profile Log in to check your private messages Log in

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support

Software Uart and External Interrupt issue

CCS Forum Index -> General CCS C Discussion

View previous topic :: View next topic

Author

Message

david90

Joined: 25 Feb 2006
Posts: 23

Software Uart and External Interrupt issue

Posted: Sun Feb 20, 2011 4:48 pm

Code:

//tested code with dev board.
#include <12F683.h>
#device adc=8

#FUSES NOWDT //No Watch Dog Timer
#FUSES INTRC //Internal RC Osc
#FUSES NOCPD //No EE protection
#FUSES NOPROTECT //Code not protected from reading
#FUSES NOMCLR //Master Clear pin used for I/O
#FUSES NOPUT //No Power Up Timer
#FUSES BROWNOUT //Reset when brownout detected
#FUSES IESO //Internal External Switch Over mode enabled
#FUSES FCMEN //Fail-safe clock monitor enabled

#use delay(clock=8000000)
#use rs232(baud=2400,parity=N,xmit=PIN_A1,rcv=PIN_A2,bits=8,errors)

int buffer[10];
int i=0;
int open_detected=0;
int close_detected=0;
void main()
{
setup_adc_ports(NO_ANALOGS|VSS_VDD);
setup_adc(ADC_OFF);
setup_timer_1(T1_DISABLED);
setup_timer_2(T2_DISABLED,0,1);
setup_comparator(NC_NC);
setup_vref(FALSE);
setup_oscillator(OSC_8MHZ);

enable_interrupts(INT_EXT);
ext_int_edge( H_TO_L );
enable_interrupts(GLOBAL); //enable interrupt

while(1)
{
output_high(PIN_A5);
delay_ms(100);
output_low(PIN_A5);
delay_ms(100);

if (open_detected==1)
{
output_high(PIN_A0);
delay_ms(100);
output_low(PIN_A0);
delay_ms(100);
output_high(PIN_A0);
delay_ms(100);
output_low(PIN_A0);
delay_ms(100);
open_detected=0;
}
if (close_detected==1)
{
output_high(PIN_A0);
delay_ms(100);
output_low(PIN_A0);
delay_ms(100);
close_detected=0;
}

}
}

#INT_EXT //use external pin int to avoid polling for serial data. Software UART does not have INT.
void INT_EXT_handler() {
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
buffer[0]=getc();

if ((buffer[0]==0x57 && buffer[1]==0xA9) || (buffer[0]==0x5F && buffer[1]==0xA1))
{
open_detected=1;
}

if (buffer[0]==0xDF && buffer[1]==0x21)
{
close_detected=1;
}
}

Whenever I power on my PIC, it immediately goes into the INT_EXT ISR and get stuck there until I send serial data to the PIC. I know for a fact that when I power up my pic, the pic doesn't even go to my infinite while loop but instead goes directly to the ISR. Why does this happen? There might be a chance that this happens because of my dev board.

temtronic

Joined: 01 Jul 2010
Posts: 9243
Location: Greensville,Ontario


Posted: Sun Feb 20, 2011 4:57 pm

You might want to enable the PowerUpTimer ( PUT) as well as and a small delay in Main before the interrupts are enabled. Depending on the board layout, power supply specs, etc. you might already have an interrupt from something 'glitchy'.

PCM programmer

Joined: 06 Sep 2003
Posts: 21708

Posted: Mon Feb 21, 2011 12:36 am

Quote:

Whenever I power on my PIC, it immediately goes into the INT_EXT ISR

Read this thread:
http://www.ccsinfo.com/forum/viewtopic.php?t=43138

Quote:

shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);
shift_left(buffer,10,0);

Why do this ? Just use a pointer or an array index.

Quote:

#FUSES INTRC

If you change this fuse to INTRC_IO then you can also use PIN_A4
as an i/o pin.

Display posts from previous:

	CCS Forum Index -> General CCS C Discussion	All times are GMT - 6 Hours
Page 1 of 1

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum