CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support
I want to work with mcp2515

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
1980best



Joined: 25 May 2007
Posts: 26

View user's profile Send private message

I want to work with mcp2515
PostPosted: Fri Oct 11, 2013 2:01 am     Reply with quote
Code:

#include <18F4550.h>
#device adc=8
#use delay(clock=20000000)
//#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8)
#fuses HS,NOWDT,NOPROTECT,NOLVP,PUT,noMCLR

#BYTE PORTA   = 0xF80
#BYTE PORTB   = 0xF81
#BYTE PORTC   = 0xF82
#BYTE PORTD   = 0xF83
#BYTE PORTE   = 0xF84

#BYTE TRISA   = 0xF92
#BYTE TRISB   = 0xF93
#BYTE TRISC   = 0xF94
#BYTE TRISD   = 0xF95
#BYTE TRISE   = 0xF96
 
#define BOARD2_ID  25
char data[8];
unsigned char len;
unsigned char stat;

int32 rx_id;
int32 tx_id;
int8 rx_len;               
int8 buffer[8];

#define CAN_USE_EXTENDED_ID TRUE
#define CAN_BRG_SEG_2_PHASE_TS TRUE 
#define CAN_BRG_PRESCALAR 4
#define CAN_BRG_SYNCH_JUMP_WIDTH 0
#define CAN_BRG_PROPAGATION_TIME 2
#define CAN_BRG_PHASE_SEGMENT_1 5
#define CAN_BRG_PHASE_SEGMENT_2 5
#define CAN_BRG_WAKE_FILTER TRUE
#define CAN_BRG_SAM FALSE

#include "can-mcp2515.c"

#USE SPI (MASTER, CLK=PIN_B1, DI=PIN_C7, DO=PIN_B0, MODE=0, BITS=8, STREAM=SPI_1)

void main()
{
can_init();

can_putd(tx_id,data,8,3,TRUE,FALSE);
can_getd(rx_id,data,len,stat);

   //Example blinking LED program
   while(true)
   {
      output_low(PIN_E0 );
      delay_ms(100);
      output_high(PIN_E0 );
      delay_ms(100);
     
      output_low(PIN_D1 );
      delay_ms(100);
      output_high(PIN_D1 );
      delay_ms(100);
     
   }

}

http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en537141

Code:

#include <can-mcp251x.h>

//IO pins connected to MCP2510ca
#ifndef EXT_CAN_CS
   #if defined(__PCD__)
      #define EXT_CAN_CS   PIN_B4
      #define EXT_CAN_SI   PIN_B0
      #define EXT_CAN_SO   PIN_C7
      #define EXT_CAN_SCK  PIN_B1

???
program stopped this here
Code:

void can_set_mode(CAN_OP_MODE mode) {
   struct struct_CANCTRL old_CANCTRL;

   memset(&old_CANCTRL,mcp2510_read(CANCTRL),1);
  // old_CANCTRL=mcp2510_read(CANCTRL);

  old_CANCTRL.reqop=mode; 

   mcp2510_write(CANCTRL, (unsigned int8)old_CANCTRL);

   do {
      memset(&old_CANCTRL,mcp2510_read(CANCTRL),1);
     //old_CANCTRL=mcp2510_read(CANCTRL);
     
   }
   while (old_CANCTRL.reqop != mode);
   
}
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Mon Oct 14, 2013 6:29 pm     Reply with quote
I think you have incorrectly swapped the pin assignments shown below.
Quote:
#define EXT_CAN_CS PIN_B4
#define EXT_CAN_SI PIN_B0
#define EXT_CAN_SO PIN_C7
#define EXT_CAN_SCK PIN_B1

I think it should be like this:
Code:
#define EXT_CAN_CS   PIN_B4
#define EXT_CAN_SI   PIN_C7
#define EXT_CAN_SO   PIN_B0
#define EXT_CAN_SCK  PIN_B1

Here is my reasoning:

The schematic of your board (on page 20) shows the SDO pin of the
PIC is on pin C7:
http://ww1.microchip.com/downloads/en/DeviceDoc/51757a.pdf

The mcp-251x.c driver has these pin assigments for SPI:
Quote:

#use spi(MASTER,MODE=0, DI=EXT_CAN_SO, DO=EXT_CAN_SI, CLK=EXT_CAN_SCK, bits=8, stream=MCP2510)

That means that EXT_CAN_SI must be defined as PIN_C7. And then
the other pin, EXT_CAN_SO must there be defined for PIN_B0.

Try the 2nd set of pin #defines above and see what happens.
1980best



Joined: 25 May 2007
Posts: 26

View user's profile Send private message

PostPosted: Sat Oct 26, 2013 5:54 pm     Reply with quote
which one true ?
ccs wizard make data in mirror !!!
you will wizard see please
Ttelmah



Joined: 11 Mar 2010
Posts: 19537

View user's profile Send private message

PostPosted: Sun Oct 27, 2013 1:25 am     Reply with quote
I don't think you will find that most programmers here use the Wizard.....

However the Wizard does not select these pins. You do, _in_ the Wizard.

The Wizard has a lot of faults (the settings to disable SPI have been wrong for many years), and in many places it makes the wrong decisions (defaulting to not enabling ERRORS when hardware RS232 is selected for example).
Don't rely on, or trust the Wizard. Do some research and work the settings out yourself.
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group