CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support
undefined identifier error

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
deltatech



Joined: 22 Apr 2006
Posts: 87

View user's profile Send private message

undefined identifier error
PostPosted: Tue May 02, 2006 7:36 am     Reply with quote
Hi I have tried to comiple this code i got this from a PIC CCS text book
but i get an error RA0_ANALOG as an undefined identifier . But if use the PIC wizard I get this code

setup_adc_ports(sAN0|VSS_VDD);

and this comiles fine . is this the same code writen differently or should the other code compile ?.

this also works setup_adc_ports(ALL_ANALOG);

but this doesnt setup_adc_ports(RA0_ANALOG);

Code:
#include <16F917.h>

#use delay(clock=4000000)

#fuses HS,NOWDT

#define  cutoff   255//128      //2.8 volts
#define  neutral_zone   25      //0.5 volts
#use delay(clock=4000000)

void main()
{

int reading;
  setup_adc_ports(RA0_ANALOG);
   setup_adc(ADC_CLOCK_INTERNAL);
set_adc_channel(0);

      while(TRUE)

      {


         reading=read_adc();

printf( reading);

//            if(reading<(cutoff-neutral_zone/2))
  //            output_high(PIN_D7);
    //        else if (reading>(cutoff+neutral_zone/2))
      //        output_high(PIN_D6);// light_one_led(RLED);
           // else
             //  light_one_led(YLED);
      }

}
dyeatman



Joined: 06 Sep 2003
Posts: 1934
Location: Norman, OK

View user's profile Send private message

PostPosted: Tue May 02, 2006 8:07 am     Reply with quote
Options change from chip to chip and for different versions of the compiler. The available options are normally found in the device header file (in this case the 16F917.H file):

// Constants used in SETUP_ADC_PORTS() are:
#define sAN0 1 //| A0
#define sAN1 2 //| A1
#define sAN2 4 //| A2
#define sAN3 8 //| A3
#define sAN4 16 //| A5
#define NO_ANALOGS 0 // None
#define ALL_ANALOG 31 // A0 A1 A2 A3 A5
Ttelmah
Guest
PostPosted: Tue May 02, 2006 8:56 am     Reply with quote
The 'key' difference, is that most (older) chips, only allow a limited number of combinations of analog inputs. On these the 'minimum' setup, with just RA0 as analog, is normally called 'RA0_ANALOG'. However latter chips (of which yours is one), allow individual analog bits to be selected, and on these, instead of having separate defines for all possible combinations, the bits are specified so that they can be 'ored' together.
This also became 'necessary' on some chips which now have so many analog inputs, and configuration options, that several hundred defines would be needed to cover them the 'old way'.
If you require reverse compatibility in this, you could just add:
#define RA0_ANALOG sAN0|VSS_VDD
and then the old definition would be 'emulated'.
As another poster has said, look at the processor's '.h' file to see the definitions for your chip.

Best Wishes
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group