Line 82: Error #118: Invalid conversion from LONG INT to INT

[kuosda]

I transfered version 1.03 from 16F877 to 18F452, I use PCWH v3.110. Make the follwing changes:

In file p16web.c

change or add address of timer1 register

16F877
//#byte TIMER_1_HIGH= 0x0f

18F452
#byte TIMER_1_HIGH= 0xfcf
#bit RD16 = 0xfcd.7 // this bit is new in 18F452 in register T1CON and controls read/write operations of timer1

change addresses of port a-c

16F877
//#byte PORTA = 5 // Main I/O ports
//#byte PORTB = 6
//#byte PORTC = 7

18F452
#byte PORTA = 0xf80 // Main I/O ports
#byte PORTB = 0xf81
#byte PORTC = 0xf82

add the RD16 = 0; command after the setup_timer_1() command in main()

setup_timer_1(TIMER1_SET); // Init timer
RD16 = 0; // new bit in 18F452, enables register read/write in two 8 bit operations

In file p16_eth.h

change address of port d-e

16F877
//#byte PORTD = 8
//#byte PORTE = 9

18F452
#byte PORTD = 0xf83
#byte PORTE = 0xf84

Error????
Line 82: Error #118: Invalid conversion from LONG INT to INT
___________________________
This message was ported from CCS's old forum
Original Post ID: 9814

[nilsener]

You have posted only the changes to make in v1.03 when transfering to 18F452, please post the complete sourcecode and mark line 82.

regards nilsener

:=I transfered version 1.03 from 16F877 to 18F452, I use PCWH v3.110. Make the follwing changes:
:=
:=In file p16web.c
:=
:=change or add address of timer1 register
:=
:=16F877
:=//#byte TIMER_1_HIGH= 0x0f
:=
:=18F452
:=#byte TIMER_1_HIGH= 0xfcf
:=#bit RD16 = 0xfcd.7 // this bit is new in 18F452 in register T1CON and controls read/write operations of timer1
:=
:=change addresses of port a-c
:=
:=16F877
:=//#byte PORTA = 5 // Main I/O ports
:=//#byte PORTB = 6
:=//#byte PORTC = 7
:=
:=18F452
:=#byte PORTA = 0xf80 // Main I/O ports
:=#byte PORTB = 0xf81
:=#byte PORTC = 0xf82
:=
:=add the RD16 = 0; command after the setup_timer_1() command in main()
:=
:=setup_timer_1(TIMER1_SET); // Init timer
:=RD16 = 0; // new bit in 18F452, enables register read/write in two 8 bit operations
:=
:=In file p16_eth.h
:=
:=change address of port d-e
:=
:=16F877
:=//#byte PORTD = 8
:=//#byte PORTE = 9
:=
:=18F452
:=#byte PORTD = 0xf83
:=#byte PORTE = 0xf84
:=
:=Error????
:=Line 82: Error #118: Invalid conversion from LONG INT to INT
___________________________
This message was ported from CCS's old forum
Original Post ID: 9820

[kuosda]

I use PCWH v3.128

p16_ip.h Line 82:
Error #118: Invalid conversion from LONG INT to INT

line 82: get_lword(remip.l) && // Sender's IP addr

Thank you!
___________________________
This message was ported from CCS's old forum
Original Post ID: 9822