 |
 |
| View previous topic :: View next topic |
| Author |
Message |
raflab
Joined: 09 Aug 2011
Posts: 6
|
| int_ext + int_timer1 problem !! |
 Posted: Fri Aug 12, 2011 6:52 am |
 |
|
my program set to 1 the PIN A1 for 5 seconds and set to 0 for the same delay !! now I'm trying to use the external interrupt using a switch related to PIN B0 !! but it doesn't work !! the timer1 still working although I disabled the timer1 interruption in external interruption's code !!
| Code: |
#include <16F628A.h>
#FUSES NOWDT //No Watch Dog Timer
#FUSES LP //Low power osc < 200 khz
#FUSES NOPUT //No Power Up Timer
#FUSES NOPROTECT //Code not protected from reading
#FUSES NOBROWNOUT //No brownout reset
#FUSES NOMCLR //Master Clear pin used for I/O
#FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O
#FUSES NOCPD //No EE protection
#use delay(clock=4000000)
#use rs232(baud=9600,parity=N,xmit=PIN_A3,rcv=PIN_A2,bits=8)
#define so 10 // définir les adresse mémoir EEPROM qu'on va les utiliser
#define mo 15
#define sf 20
#define mf 25
unsigned int16 count=0;
#int_ext
void ext_isr()
{
disable_interrupts(int_timer1);
count=0;
output_high(pin_a2);
output_low(pin_a1);
enable_interrupts(int_timer1);
}
#int_timer1
void timer1(){
count++;
}
int16 delay=0;
void main()
{
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1);
setup_timer_2(T2_DISABLED,0,1);
setup_comparator(NC_NC_NC_NC);
setup_vref(FALSE);
//Setup_Oscillator parameter not selected from Intr Oscillotar Config tab
set_timer1(delay);
EXT_INT_EDGE(H_TO_L);
setup_timer_1(T1_INTERNAL|T1_DIV_BY_8);
enable_interrupts(INT_EXT);
enable_interrupts(INT_TIMER1);
enable_interrupts(GLOBAL);
while(1){
while(count<=10){
output_high(pin_a1);}
count=0;
while(count<=10){
output_low(pin_a1);}
count=0;
}
}
|
|
|
 |
Ttelmah
Joined: 11 Mar 2010
Posts: 19539
|
|
| Posted: Fri Aug 12, 2011 8:10 am |
|
|
You do realise that as shown, the timer will be disabled for only about 30uSec.
The EXT interrupt only triggers when there is an _edge_ on the external pin. Not a level. Just for 30uSec or so, while the int_ext is serviced (for the whole time, nothing to do with your disable instructions - the _hardware_ disables all other interrupts when one is being serviced), the timer will be disabled, and then re-enabled when the routine exits. Since the timer triggers about every 1000uSec, this will make no difference at all to the operation of the timer.
Best Wishes |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ 
Search
Register
Profile 
Log in to check your private messages 
Log in
