| View previous topic :: View next topic |
| Author |
Message |
Knight_FlyCn
Joined: 10 May 2013
Posts: 16
Location: Việt Nam
|
| Who can help me ? UART PIC18F4620 and ZigBee |
 Posted: Tue May 14, 2013 4:17 am |
 |
|
| Code: | #include <Coordinator.h>
#include "def_18f4620.c"
#include "slave_2_tx_rx.h"
#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8)
#define SPI_MODE_0 (SPI_L_TO_H | SPI_XMIT_L_TO_H)
#bit CS = 0xF80.4
#bit RST = 0xF82.2
#bit INT_ = 0xF81.0
#bit WAKE = 0xF82.1
#bit CS_Direction = 0xF92.4
#bit RST_Direction = 0xF94.2
#bit INT_Direction = 0xF93.0
#bit WAKE_Direction = 0xF94.1
INT TEMP;
INT COMMAND,adress_surport=0x01;
const int IP_request=0x00,ip_surport=0x10;
#INT_EXT
void ngat_RB0()
{
temp = read_ZIGBEE_short(INTSTAT); // Read and flush register INTSTAT
if ((temp&(1<<3))==(1<<3))
{ rc0=rd3=!rd3;
read_RX_FIFO();
command=data_rx[0];
switch (command)
{
case IP_request:
adress_surport++;
PAN_ID_destination[0] = PAN_ID[0];
PAN_ID_destination[1] = PAN_ID[1];
address_short_destination[0] = rfd_address_short[0];
address_short_destination[1] = rfd_address_short[1];
PAN_ID_source[0] = PAN_ID[0];
PAN_ID_source[1] = PAN_ID[1];
address_short_source[0] = coord_address_short[0];
address_short_source[1] = coord_address_short[1];
data_tx[0]=ip_surport;
data_tx[1]=adress_surport;
write_TX_normal_FIFO();
break;
}
}
DISABLE_INTERRUPTS(INT_EXT);
}
void main()
{
TRISB1=TRISB2=TRISB3=1;
TRISC0=TRISD3=0;
CS_Direction = 0; // Set direction to be output
RST_Direction = 0; // Set direction to be output
INT_Direction = 1; // Set direction to be input
WAKE_Direction = 0; // Set direction to be output
rc0=rd3=1;
Delay_ms(5);
setup_spi(SPI_MASTER | SPI_MODE_0 | SPI_CLK_DIV_4); // Initialize SPI module
pin_reset(); // Activate reset from pin
software_reset(); // Activate software reset
RF_reset(); // RF reset
set_WAKE_from_pin(); // Set wake from pin
set_long_address(ADDRESS_long_2);
set_short_address(coord_address_short); // Set short address
set_PAN_ID(PAN_ID); // Set PAN_ID
init_ZIGBEE_nonbeacon(); // Initialize ZigBee module
nonbeacon_PAN_coordinator_device();
set_TX_power(31); // Set max TX power
set_frame_format_filter(1); // 1 all frames, 3 data frame only
set_reception_mode(1); // 1 normal mode
delay_ms(10);
enable_int();
pin_wake(); // Wake from pin
enable_interrupts(GLOBAL);
enable_interrupts(INT_EXT);
ext_int_edge(H_to_L);
while (1)
{
enable_interrupts(INT_EXT);
}
} |
I do not know what the above command made the connection to the computer. To transfer data to and from RFD to Coodinator computer.
---> Who can help me ? what line code ?
_________________
Thinh |
|
 |
temtronic
Joined: 01 Jul 2010
Posts: 9241
Location: Greensville,Ontario
|
|
| Posted: Tue May 14, 2013 6:00 am |
|
|
Without seeing what's in these files...
#include <Coordinator.h>
#include "def_18f4620.c"
#include "slave_2_tx_rx.h"
... it's nearly impossible to help you.
It appears that a Zigbee module is connected via SPI mode to a PIC and that 'something' interrupts the PIC on the B0 pin,triggering the ISR,'stuff' is done including...
write_TX_normal_FIFO();
...which may or may not be sending Zigbee data to the PC..
again, very very hard to figure out unless the 3 files are shown.
hth
jay |
|
|
Ttelmah
Joined: 11 Mar 2010
Posts: 19537
|
|
| Posted: Tue May 14, 2013 6:08 am |
|
|
and the code is appalling.
What is the point of sitting in a loop continuously enabling an interrupt. Why is it ever turned off?. Then the 'form' suggests this has possibly been ported from another compiler, by someone who has little or no knowledge of CCS. |
|
|
|
FAQ 
Search
Register
Profile 
Log in to check your private messages 
Log in
