Simple electronic compass

[Gerrit]

Hello all,

I'm looking for a simple design of een electronic compass.

I need aproxamatly 15� resolution

Does any one have a schematic and a simple piece of source code?


Reagrds,

Gerrit
___________________________
This message was ported from CCS's old forum
Original Post ID: 144515973

[Dave Yeatman]

Gerrit,
Try this electronic compass. Easy to interface to the PIC.

<a href="http://www.dinsmoresensors.com/" TARGET="_blank">http://www.dinsmoresensors.com/</a>

Dave

:=Hello all,
:=
:=I'm looking for a simple design of een electronic compass.
:=
:=I need aproxamatly 15� resolution
:=
:=Does any one have a schematic and a simple piece of source code?
:=
:=
:=Reagrds,
:=
:=Gerrit
___________________________
This message was ported from CCS's old forum
Original Post ID: 144515974

[R.J.Hamlett]

:=Hello all,
:=
:=I'm looking for a simple design of een electronic compass.
:=
:=I need aproxamatly 15� resolution
:=
:=Does any one have a schematic and a simple piece of source code?
:=
:=
:=Reagrds,
:=
:=Gerrit
I have a design I did some time ago, based on the '1655' analogue compass sensor (this has a tiny magnetic compass needle, used as a 'magnetic amplifier', to give a much larger signal change, than is seen from 'fluxgate' compasses), using a 16C71, to drive a digital pot, giving 0-99, round the circle. The circuit was designed to allow this to directly drive the Lego 'mindstorms' robotic system. The code is in CCS C. The circuit is fairly simple (but does contain all the extra 'interface' hardware, to connect the unit to the mindstorms system. I use the watchdog, to allow the chip to sleep for a large amount of the time, switching off the compass itself at the same time, to minimise power consumption.
I could send you the circuits, and the code 'direct', if you give me an email address.

Best Wishes
___________________________
This message was ported from CCS's old forum
Original Post ID: 144515984

[Gerrit]

Hello Hamlett,

I would be very interested in a simple design.
And sample (source) code in CCS C.

My e-mail address is [email protected].

Thank you al ready for your help.

Regards,

Gerrit Faas

:=:=Hello all,
:=:=
:=:=I'm looking for a simple design of een electronic compass.
:=:=
:=:=I need aproxamatly 15� resolution
:=:=
:=:=Does any one have a schematic and a simple piece of source code?
:=:=
:=:=
:=:=Reagrds,
:=:=
:=:=Gerrit
:=I have a design I did some time ago, based on the '1655' analogue compass sensor (this has a tiny magnetic compass needle, used as a 'magnetic amplifier', to give a much larger signal change, than is seen from 'fluxgate' compasses), using a 16C71, to drive a digital pot, giving 0-99, round the circle. The circuit was designed to allow this to directly drive the Lego 'mindstorms' robotic system. The code is in CCS C. The circuit is fairly simple (but does contain all the extra 'interface' hardware, to connect the unit to the mindstorms system. I use the watchdog, to allow the chip to sleep for a large amount of the time, switching off the compass itself at the same time, to minimise power consumption.
:=I could send you the circuits, and the code 'direct', if you give me an email address.
:=
:=Best Wishes
___________________________
This message was ported from CCS's old forum
Original Post ID: 144515986

[R.J.Hamlett]

:=Hello Hamlett,
:=
:=I would be very interested in a simple design.
:=And sample (source) code in CCS C.
:=
:=My e-mail address is [email protected].
:=
:=Thank you al ready for your help.
:=
:=Regards,
:=
:=Gerrit Faas
OK it is on it's way...

Best Wishes

:=
:=:=:=Hello all,
:=:=:=
:=:=:=I'm looking for a simple design of een electronic compass.
:=:=:=
:=:=:=I need aproxamatly 15� resolution
:=:=:=
:=:=:=Does any one have a schematic and a simple piece of source code?
:=:=:=
:=:=:=
:=:=:=Reagrds,
:=:=:=
:=:=:=Gerrit
:=:=I have a design I did some time ago, based on the '1655' analogue compass sensor (this has a tiny magnetic compass needle, used as a 'magnetic amplifier', to give a much larger signal change, than is seen from 'fluxgate' compasses), using a 16C71, to drive a digital pot, giving 0-99, round the circle. The circuit was designed to allow this to directly drive the Lego 'mindstorms' robotic system. The code is in CCS C. The circuit is fairly simple (but does contain all the extra 'interface' hardware, to connect the unit to the mindstorms system. I use the watchdog, to allow the chip to sleep for a large amount of the time, switching off the compass itself at the same time, to minimise power consumption.
:=:=I could send you the circuits, and the code 'direct', if you give me an email address.
:=:=
:=:=Best Wishes
___________________________
This message was ported from CCS's old forum
Original Post ID: 144515988

[Chang-Huei Wu]

Dear R. J.

I am very interested in your 1655 design (curently using Honeywell's HMR3300 and Vector 2X), please give me a kick to start it again,

My e-mail: [email protected]

Thanks a lot,

Chang-Huei Wu

:=I have a design I did some time ago, based on the '1655' analogue compass sensor (this has a tiny magnetic compass needle, used as a 'magnetic amplifier', to give a much larger signal change, than is seen from 'fluxgate' compasses), using a 16C71, to drive a digital pot, giving 0-99, round the circle. The circuit was designed to allow this to directly drive the Lego 'mindstorms' robotic system. The code is in CCS C. The circuit is fairly simple (but does contain all the extra 'interface' hardware, to connect the unit to the mindstorms system. I use the watchdog, to allow the chip to sleep for a large amount of the time, switching off the compass itself at the same time, to minimise power consumption.
:=I could send you the circuits, and the code 'direct', if you give me an email address.
:=
:=Best Wishes
___________________________
This message was ported from CCS's old forum
Original Post ID: 144516027

[Chang-Huei Wu]

Dear R. J.
I am very interested in your 1655 design (curently using Honeywell's HMR3300 and Vector 2X), please give me a kick to start it again,

My e-mail: [email protected]

Thanks a lot,

Chang-Huei Wu

:=I have a design I did some time ago, based on the '1655' analogue compass sensor (this has a tiny magnetic compass needle, used as a 'magnetic amplifier', to give a much larger signal change, than is seen from 'fluxgate' compasses), using a 16C71, to drive a digital pot, giving 0-99, round the circle. The circuit was designed to allow this to directly drive the Lego 'mindstorms' robotic system. The code is in CCS C. The circuit is fairly simple (but does contain all the extra 'interface' hardware, to connect the unit to the mindstorms system. I use the watchdog, to allow the chip to sleep for a large amount of the time, switching off the compass itself at the same time, to minimise power consumption.
:=I could send you the circuits, and the code 'direct', if you give me an email address.
:=
:=Best Wishes
___________________________
This message was ported from CCS's old forum
Original Post ID: 144516028

[Kamarul]

Hello Hamlett,

I would also like to have your design and the source code. Could you please email them to me at [email protected].

Thank you in advance.
___________________________
This message was ported from CCS's old forum
Original Post ID: 144516042

[R.J.Hamlett]

:=Dear R. J.
:=
:=I am very interested in your 1655 design (curently using Honeywell's HMR3300 and Vector 2X), please give me a kick to start it again,
:=
:=My e-mail: [email protected]
:=
:=Thanks a lot,
:=
:=Chang-Huei Wu
OK. Have forwarded the design to you.

Best Wishes


:=:=I have a design I did some time ago, based on the '1655' analogue compass sensor (this has a tiny magnetic compass needle, used as a 'magnetic amplifier', to give a much larger signal change, than is seen from 'fluxgate' compasses), using a 16C71, to drive a digital pot, giving 0-99, round the circle. The circuit was designed to allow this to directly drive the Lego 'mindstorms' robotic system. The code is in CCS C. The circuit is fairly simple (but does contain all the extra 'interface' hardware, to connect the unit to the mindstorms system. I use the watchdog, to allow the chip to sleep for a large amount of the time, switching off the compass itself at the same time, to minimise power consumption.
:=:=I could send you the circuits, and the code 'direct', if you give me an email address.
:=:=
:=:=Best Wishes
___________________________
This message was ported from CCS's old forum
Original Post ID: 144516049

[R.J.Hamlett]

:=Hello Hamlett,
:=
:=I would also like to have your design and the source code. Could you please email them to me at [email protected].
:=
:=Thank you in advance.
Ok. On it's way to you as well.

I notice Mr Chang-Huei Wu, has sent me a 'private' post. These never seem to work (have a look back for comments about this 'feature' of the board...). He should have my direct email now, so if you want to talk privately, 'drop me a mail'. :-)

Best Wishes
___________________________
This message was ported from CCS's old forum
Original Post ID: 144516051

[Chang-Huei Wu]

:=I notice Mr Chang-Huei Wu, has sent me a 'private' post. These never seem to work (have a look back for comments about this 'feature' of the board...). He should have my direct email now, so if you want to talk privately, 'drop me a mail'. :-)
:=
:=Best Wishes

Got it!

Thanks a lot

Chang-Huei Wu
___________________________
This message was ported from CCS's old forum
Original Post ID: 144516054