CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support

Ultrasonic Distance Finder using 4MHz Oscillator

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
rahi_044



Joined: 08 Nov 2011
Posts: 3

View user's profile Send private message Send e-mail

Ultrasonic Distance Finder using 4MHz Oscillator
PostPosted: Sun Dec 11, 2011 1:35 am     Reply with quote

I am trying to measure distance using 4MHz external oscillator and PIC16F877A. But the timer value is not stable. Here is my code:
Code:

#include <16F877A.h>
#device adc=8
#FUSES NOWDT, XT, NOPUT, PROTECT, NOBROWNOUT, NOLVP, NOCPD, NOWRT, NODEBUG
#use delay(clock=4000000)

#include <lcd.c>

int16 flg = 0;
int16 flgTemp = 0;
int16 distance = 0, time = 0;

#int_ccp1
void isr()

 /*
 rise = CCP_1;
 //CCP_1 is the time the pulse went high
 
     fall = CCP_2;
 //CCP_2 is the time the pulse went low
 
     pulse_width = fall - rise;
 //pulse width
 */
}

#int_EXT
void  EXT_isr(void)
{
   flgTemp = flg;
   flg = 25;
}

#int_TIMER0
void  TIMER0_isr(void)
{
   flg ++;
   if(flg > 20) flg = 0;
}

void main()
{
   set_tris_a(0b00000001);
   
   lcd_init();                                        // initiating timer
   printf(LCD_PUTC, "\fTest 2");
   delay_ms(1000);
   
   setup_timer_2(T2_DIV_BY_1, 24, 1);                 // For 4 MHz Oscillator
   set_pwm1_duty(12);
   
   setup_CCP1(CCP_OFF);
   output_low(PIN_C2);
   delay_ms(10);
     
   setup_timer_0(RTCC_INTERNAL|RTCC_DIV_8);           // (RTCC_EXT_L_TO_H|RTCC_DIV_32);      //(T1_INTERNAL|T1_DIV_BY_8);         // initiating timer
   setup_timer_1(T1_INTERNAL|T1_DIV_BY_8);            // initiating timer
     
   enable_interrupts(INT_EXT);                        // Enable Interrupts
   enable_interrupts(GLOBAL);
   
   while(true)
   {                   
      switch(flg)
      {
         case 0:                                      // 0 ms
            setup_ccp1(CCP_PWM);   
            set_timer1(0);                            // setting timer zero
            break;
           
         case 1:                                      // 2 ms           
            setup_CCP1(CCP_OFF);
            output_low(PIN_C2);
            break;
           
         case 25:                                     // EXT_INT           
            disable_interrupts(INT_EXT);               // Disable Interrupts
            //disable_interrupts(GLOBAL);

            //while(input(PIN_A0))                        // Wait for high state of echo pin
            //{ }

            time = get_timer1();                      // Getting the time
            distance = time*0.028 + 1.093 ;           // Calculating the distance
                                         
            printf(lcd_putc,"\fTime :%Lu \nDistance :%Lu",time,distance);
            delay_ms(2000);
           
            flg = flgTemp;
           
            enable_interrupts(INT_EXT);                        // Enable Interrupts
            //enable_interrupts(GLOBAL);   
            break;

         default:
            break;
      }
   }
}

Can anyone give me an implemented CCS code please, I will convert it on my demand.
Ttelmah



Joined: 11 Mar 2010
Posts: 19539

View user's profile Send private message

PostPosted: Sun Dec 11, 2011 6:20 am     Reply with quote

Several comments, a lot relating to 'how does your hardware work':
1) You talk about an external oscillator, but have 'XT' selected, which is for driving a crystal.
2) Why are you looking at a pulse width?. Normally for ultrasonic, you have a pulse 'burst' being sent, and a similar burst being received. The hardware needs to have a narrowband filter detecting the signal train, followed by an peak detector circuit to give an 'envelope' corresponding to the signal from the transducer. Normally with an AGC circuit so that the sensitivity increases when signals are not seen. The code first, needs to ignore signals for a short time during and after the transmission burst - otherwise you will detect this, not the reflection. Then look for the rising edge on the envelope.
You can't directly look for pulses from the transducer, or you _will_ see every percussive signal in range....
3) Why fiddle with interrupts?. At the end of the day, the code is doing nothing while you wait for a return, so do this in the main loop. Just set a timer to zero when you send the pulse burst, and read it when you see the return. If it overflows, then you have almost certainly not had a successful reflection, so need to try again.
4) Why waste processor time using int16 for flg, and flgtemp. Values seem to always be 30 or less...
5) What on earth is flgtemp for?. Seems to be wasting time and space.

Best Wishes
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sun Dec 11, 2011 1:22 pm     Reply with quote

1. Post the manufacturer and model number of your Ultrasonic Range Finder.

2. Post a link to the webpage that has the data sheet for it.

3. Post your CCS compiler version.
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group