GPRS and cash

Scarr · Guest

Hi,
I need somone to REALLY help me, by REALLY I mean "hold my hand" and be avaliable when I need them to ADD GPRS functionallity to my code, either that or put the GPRS code in for me. I am willing to pay as I don't have the time to get my head round it.

Anyone intrested?

Scarr · Guest

Forgot to mention I have GSM with stack.

Thx

Scarr · Guest

Come on guys!!! there must be someone out there, I will pay �1000.00 if we can get it up and running in a week.

Can pay via paypal......

here if the PDF for the GSM take a look I don't think someone with GPRS experience will have a problem.

http://www.roundsolutions.com/pdf/Telit/RS-Easy-GPRSv2.pdf

Hans Wedemeyer · Joined: 15 Sep 2003 Posts: 226

Guest · Posted: Wed Oct 22, 2003 4:54 pm

Your telling me a embedded C programmer can earn >�4000 for a weeks work

I'm moving over stright away, were do you live!!!!

Over here 1k per week is a good wage trust me

Scarr · Guest

It to simple establish the GPRS connection and send / receive a block of data.

If it takes you ten mins then all the better.

Thx

ik1wvq · Guest

hi,
use the GPRS modem TELIT GM862 GPRS
www.gm862.com
the GPRS attach is COMPLETLY achived by internal firmware.
you simply issue an AT+ like command, specifiing the
IP address, PORT number, packet type (UDP or TCP)
and then the modem connect itself to the internet word,
make the packet with data entered into the serial port,
and send the packet to the specified IP address...

few firmware line and the job is done ..
GREAT !!!

regards

Mauro

Bad_Mujo · Guest

If You email me some more info (like target processor and things like that) I can see what I can do for You.

[email protected]

karth · Joined: 10 Sep 2003 Posts: 29

Can you email the details and i'll see if i can help

Scarr · Guest

So here are the quetions so far.

1) I have WAP enabled on my SIM is it therefore GPRS enabled? or are all SIM's GPRS enabled (as long as the network is GPRS enabled)

2) My sim is a Orange SIM does this mean I should use "AT+CGDCONT = 1,"IP","Orange","0.0.0.0",0,0<cr>"?, If not how do I find out what APN to use.

3) Is using 0.0.0.0 basically asking for a IP address?

4) The AT#USERID returns ERROR, I send AT#USERID="Ben Hoelke" and get back ERROR

5) Same with AT#PASSW

6) Once connected is that connection always there even as I move between Cells and loose signal?

The example below is taken from the PDF for the GSM

AT+CGDCONT = 1,"IP","internet.gprs","0.0.0.0",0,0<cr>
AT#USERID="Ben Hoelke"<cr>
AT#PASSW="EASY GPRS"<cr> AT#SKTSET=0,80,"www.roundsolutions.com"<cr>
AT#SKTOP

Hans Wedemeyer · Joined: 15 Sep 2003 Posts: 226

Scarr · Guest

Do you live in USA?

Hans Wedemeyer · Joined: 15 Sep 2003 Posts: 226

karth · Joined: 10 Sep 2003 Posts: 29

my email address is [email protected], email the full details. modem type, etc...

Ian McCrum · Joined: 26 Oct 2003 Posts: 14 Location: Northern Ireland

Hi, I posted a message on the bulletin board run by the mobile phone unit that you are using, search that board for

re: GPRS Email in the UK ( Orange) example - 10.06.2003, 21:57:09

The bulletin board is at
http://www.modem-gsm.de/forum/

Basically I just use a PIC to drive the GPRS stack builtin to the mobile phone. I am only sending email and the response back to the PIC are bound to be short so I do not use handshake on the rs232 lines. It has not been a problem with the short emails that I send.

It was a days work to "port" from an existing CSD application, just meant removing a lot of the PIC code, previously I was using a firmware PPP module and using the phone as a 9600 baud modem.

In terms of ensuring the data got sent, there is sufficient handshake in the email protocol to ensure it reached the email server ok.... better would be a complete packet driven client/server ... maybe beter to use tftp and check a checksum... email me if you wish IJ.McCrum <AT> ulster.ac.uk
_________________
Ian McCrum, email address held at
www.eej.ulst.ac.uk/~ian