CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support

Write and read in EEPROM of PIC 16F877A [Solved]

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
emazzu630



Joined: 14 Aug 2018
Posts: 20
Location: Ouro Verde - SC

View user's profile Send private message

Write and read in EEPROM of PIC 16F877A [Solved]
PostPosted: Fri Feb 08, 2019 11:14 pm     Reply with quote

Via the "S0" and "S1" button I change the "up" "down" addresses of the
eeprom memory, and "S2" and "S3" to "write" and "read" in the
addresses and it works very well. I can store values of "8 bits" correctly. I
have tried several examples in "16 bits", but it did not work.
Has anyone taken an equal situation and is willing to help me?
Code:

#include <16F877a.h>
#fuses HS, NOWDT, NOPROTECT, NOBROWNOUT, NOLVP, NOCPD, PUT
#use delay(clock=4000000)

#use fast_io(a)
#use fast_io(b)
#use fast_io(c)
#use fast_io(d)

#byte porta  = 0x05
#byte portb  = 0x06
#byte portc  = 0x07
#byte portd  = 0x08

#byte trisa  = 0x85
#byte trisb  = 0x86
#byte trisc  = 0x87
#byte trisd  = 0x88


///////////////////
// (code here) //
///////////////////

//**********************************************************

void mem_eeprom() {

///////////////////
// (codigo aqui) //
///////////////////

   if (S3 == 0)
      write_eeprom(adress, data);     // write data in eeprom
   
   if (S2 == 0) {
      data = read_eeprom(adress);    // writes data on 74hc595
      while (S2 == 0);                       // wait to release S2
   }
}

//**********************************************************

void main() {

///////////////////
// (codigo aqui) //
///////////////////

   trisa = 0b11111111;
   trisb = 0b00000000;               // set the ports
   trisc = 0b01011111;
   trisd = 0b00000000;
   delay_ms(200);

   

while (true){
   mem_eeprom();
   }
}
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sat Feb 09, 2019 3:23 am     Reply with quote

Look at the CCS driver file internal_eeprom.c.
It has these routines to write to 16-bit integers:
Quote:

void write_int16_eeprom(address, int16 data)

void write_int16_eeprom(address, int16 data)
Ttelmah



Joined: 11 Mar 2010
Posts: 19529

View user's profile Send private message

PostPosted: Sat Feb 09, 2019 3:36 am     Reply with quote

There is though an 'issue' with the posted code. If your switch is held on for
even a short time, a lot of EEPROM 'lives' will be used.
Every time you call the write, it uses up a life. Hold the switch down for half
a second, and a hundred lives will have been used.... Sad
Do this at all often, and the EEPROM will be killed.
Code:

   if (S3 == 0)
   {
      int temp2;
      temp2=read_eeprom(adress);
      if (temp2!=data)
         write_eeprom(adress, data);     // write data in eeprom
   }

This way it'll read what is already in the EEPROM, and only write if the new
'data' is different. Result a life is only used when the data changes. Hold
the button down, and only one write will occur.
emazzu630



Joined: 14 Aug 2018
Posts: 20
Location: Ouro Verde - SC

View user's profile Send private message

PostPosted: Sat Feb 09, 2019 7:54 am     Reply with quote

Obrigado PCM programmer, Ttelmah... A ajuda deverá ser importante.

Last edited by emazzu630 on Sun Feb 24, 2019 5:41 pm; edited 5 times in total
Ttelmah



Joined: 11 Mar 2010
Posts: 19529

View user's profile Send private message

PostPosted: Sat Feb 09, 2019 8:54 am     Reply with quote

PCM_programmer has already pointed you to the code for the int16.

Just include "internal_eeprom.c". It gives you functions that work exactly
like the single byte write, but with versions that support int1, int16, int32,
int48, float, int64 etc..

All of the codes you post look as if they should also work.

Remember the address will have to increment in 2's if you are writing
int16's. So you can't write an int16 to address 0, and then another to
address 1. You would need to write the second to address 2 etc..
emazzu630



Joined: 14 Aug 2018
Posts: 20
Location: Ouro Verde - SC

View user's profile Send private message

PostPosted: Sun Feb 24, 2019 5:23 pm     Reply with quote

After adding the "internal_eeprom.c" library and writing the code below,
with the counter for eeprom from 2 to 256, everything is working correctly
with write and read int16.
Code:

if (S5 == 0) {
   int16 temp2;
   temp2 = read_int16_eeprom (adress);
   if (temp2 != data) {
   write_int16_eeprom( adress, data);  // write data to eeprom
   }
   
   if (S4 == 0) {
   data = read_int16_eeprom(adress);    // read data in eeprom and writes it to the 74HC595 and display
   while (S4 == 0);                             // wait while "S4" is low
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group