Please Help me about Software Serial.

[A]

Please Help me about Software Serial.

I receive error data from other microcontroller. i use pic18f458 and pic16f876
When i receive data from pic16f876 sent to board 18f458. data is ok but when i sent data from 18f458 to 16f876 data is error
because i use one wire communication and have some problem about #INT_RB in pic16f876
On circuit board 18f458. i use RB0 like External interrupt. it receive data ok. but on pic16f876 board i must use rb6 for
crystal 3.579545MHz or 4000000 MHz and i must use rb7 to receive data from pic18f458. Then i use #INT_RB but it have
some big problem about one wire serial. because #int_rb is run all the time and i can't do anything in loop main.
below is my sourcecode for pic18f458

this source is send data{ 'A','B',0x02,'C','D' }; from 16f876 to 18f458 receive data ok because i send data from pic18f458 to pc
and send data { 'E','F',0x02,'G','H' }; back to pic16f876 but data is error. i know because i use lcd check data from pic16f876

Please help me. how i should solve this problem in #INT_RB in pic16f876 to receive data correct
because it very important for me. because i must use this for my thesis. if i can't solve this problem. i must change thesis. :(
Please.... Thank you for all help. Hope someone can help me from this big problem
and i must communicate at baud 9600
//===============================================================
#include <18F458.h>
#device adc=8
#use delay(clock=4000000,RESTART_WDT)
#fuses NOWDT,WDT128,XT, NOPROTECT, NOOSCSEN, BROWNOUT, BORV45, PUT, NOCPD, NOSTVREN, NODEBUG, NOLVP, NOWRT, NOWRTD, NOWRTB, NOCPB, NOWRTC, NOEBTR, NOEBTRB
#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8,stream=PC_DATA)
#use rs232(baud=9600,parity=N,xmit=PIN_B0,rcv=PIN_B0,bits=8,stream=MCU_DATA)
#use i2c(Master,Fast,sda=PIN_C4,scl=PIN_C3)

#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#ZERO_RAM

#define BUFFER_SIZE 32

register byte buffin[BUFFER_SIZE];
register byte buffout[BUFFER_SIZE];
register BYTE buffer[BUFFER_SIZE];

BYTE next_in = 0;
BYTE next_out = 0;

int CIN=0;

#define RS PIN_C0
#define RW PIN_C1
#define EN PIN_C2

#define SE1 PIN_A1
#define SE2 PIN_A2

#define CARD_IN !input(PIN_B1)
.....
....
#int_EXT
EXT_isr()
{
int t;

if(kbhit(MCU_DATA))
{
buffer[next_in]=fgetc(MCU_DATA);
t=next_in;
next_in=(next_in+1) % BUFFER_SIZE;
if(next_in==next_out)
{
next_in=t; // Buffer full !!
}
}
}

#define bkbhit (next_in!=next_out)
BYTE bgetc()
{
BYTE c;

while(!bkbhit);
c=buffer[next_out];
next_out=(next_out+1) % BUFFER_SIZE;
return(c);
}

void get_packet( byte * packet_ptr )
{
int clen=0;

packet_ptr[0]=bgetc(); //nad
packet_ptr[1]=bgetc(); //pcb
packet_ptr[2]=bgetc(); //len

for(clen=0;clen<packet_ptr[2];clen++)
{
packet_ptr[clen+3]=bgetc();
packet_ptr[clen+4]='\0';
}
}

void send_packet( byte * packet_out , int len_out_packet )
{
int copacket=0;

disable_interrupts(GLOBAL);
for(copacket=0;copacket<len_out_packet;copacket++)
{
fputc(packet_out[copacket],mcu_data);
delay_us(1000);
}
enable_interrupts(GLOBAL);
}

void main()
{
byte EFGH[5]={ 'E','F',0x02,'G','H' };

port_b_pullups(TRUE);
setup_adc_ports(NO_ANALOGS);
setup_adc(ADC_OFF);
setup_psp(PSP_DISABLED);
setup_wdt(WDT_OFF);
setup_timer_0(RTCC_OFF);
setup_timer_1(T1_DISABLED);
setup_timer_2(T2_DISABLED,0,1);
setup_timer_3(T3_DISABLED|T3_DIV_BY_1);
setup_comparator(NC_NC_NC_NC);

ext_int_edge( h_to_l );
disable_interrupts(INT_EXT);
disable_interrupts(GLOBAL);

CIN==0;
next_in=0;
next_out=0;
out_led(0x00);

while(true)
{
if(CARD_IN)
{
if(CIN==0)
{
delay_ms(500);
CIN=1;

fprintf(PC_DATA,"\nCard Inserted.\n");
enable_interrupts(global);
enable_interrupts(int_ext);

output_low(Pin_A5);
delay_ms(10);
output_high(Pin_A5);
}
out_led(0x02);
get_packet(buffin);
fprintf(PC_DATA,"%S",buffin);
delay_ms(500);
send_packet(EFGH,5); // send data to pic16f876 but error ???????????????????
}
else
{
out_led(0x03);
CIN=0; Next_in=0; Next_out=0;
}
}
}

and below is sourcecode for pic16f876

//==================================================================
#include <16F876.h>
#device *=16
#device adc=8
#use delay(clock=4000000,RESTART_WDT)
#fuses NOWDT,XT, PUT, NOPROTECT, BROWNOUT, NOLVP, NOCPD, NOWRT, NODEBUG
#define EEPROM_SDA PIN_B4
#define EEPROM_SCL PIN_B5
#use rs232(baud=4800,parity=N,xmit=PIN_B7,rcv=PIN_B7,bits=8,stream=MCU_DATA)
#use i2c(Master,Fast,sda=PIN_B4,scl=PIN_B5)

#include <2465.C>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#ZERO_RAM

#define BUFFER_SIZE 32

#priority rb,rtcc

register byte buffin[BUFFER_SIZE];
register byte buffout[BUFFER_SIZE];
register BYTE buffer[BUFFER_SIZE];

BYTE next_in = 0;
BYTE next_out = 0;

int codata1=0;
int cout=0;
char odata[5]={ 'A','B',0x02,'C','D' };

#define RW PIN_A0
#define RS PIN_A1
#define EN PIN_A2

#define LED0 PIN_A3
#define LED1 PIN_A4

void send_packet( byte * packet_out , int len_out_packet )
{
int copacket=0;

disable_interrupts(INT_RB);
disable_interrupts(GLOBAL);

for(copacket=0;copacket<len_out_packet;copacket++)
{
fputc(packet_out[copacket],mcu_data);
delay_us(100);
}
enable_interrupts(GLOBAL);
}

#int_RTCC
RTCC_isr()
{
char Hello[]="Hello";
int checkc;

disable_interrupts(INT_RTCC);

for(checkc=0;checkc<5;checkc++)
{
Wcharxy(1,(checkc+1),buffin[checkc]); // write to lcd
}
}

#int_RB
RB_isr()
{
if(kbhit(MCU_DATA))
{
disable_interrupts(INT_RB);
buffin[next_in]=fgetc(MCU_DATA);
buffin[next_in+1]='\0';
next_in++;
enable_interrupts(INT_RB);

}
if(next_in==4)
{
buffin[next_in+1]='\0';
disable_interrupts(INT_RB);
enable_interrupts(INT_RTCC);
next_in=0;
}
}

void main()
{

port_b_pullups(TRUE);
setup_adc_ports(NO_ANALOGS);
setup_adc(ADC_OFF);
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1);
setup_timer_1(T1_DISABLED);
setup_timer_2(T2_DISABLED,0,1);
init_ext_eeprom();

init_lcd();

disable_interrupts(INT_RTCC);
disable_interrupts(INT_RB);
disable_interrupts(GLOBAL);

next_in=0; Next_out=0;

while(1)
{
send_packet(odata,5);
enable_interrupts(INT_RB);
}
}

[a]

sorry for my false in my code. but true sourcecode is
//==================================================================
#include <16F876.h>
....
....
#use rs232(baud=9600,parity=N,xmit=PIN_B7,rcv=PIN_B7,bits=8,stream=MCU_DATA)

baud 9600
but this code is not work data is not correct.
Please Help me????

[Humberto]

1) Be aware that RB7 share the interrupt trigger with RB6, RB5 and RB4.
2) Don�t need to manipulate interrupts enables/disables inside the isr.
Let the compiler to do so.
3) Receiving the incomming data in RB7, every time it change (H-L / L-H)
will trigger an RB_INT.

Work around is doing a dirty work of wiring RB0 as RCV pin instead of
RB7 and using EXT_INT to trigger the software UART handler.

Best wishes,

Humberto

[Mark]

[Humberto]

Mark wrote:

[Mark]

[A]

To humberot
i must use RB7 is receiver and transmitter because i must use it as smartcard
pic16f876+24lc64 and pin rb6 is clock and rb7 is data. i must use rb7 for receive and transmit.
when i use rb7 as receive data in software serial. i will disable_rtcc and when receive data
complete i will disable_rb and enable_rtcc. because i think i will use rtcc for print data to lcd
and check data on lcd. And i disable_rtcc in #INT_RTCC. because i thing when i print data to lcd
it should use a long time and rtcc may be overflow before i show data on lcd complete.

[A]

To Mark
i don't know. what is the Port B values. please example this value. because i am a new
programmer for this compiler and i must use rb7 for receive and transmit data between
pic16f876 and pic18f458 and this is very simple code in #int_rb.
but it receive data error
and when i send data from pic16f876 to pic18f458. Pic18f458 is receive data OK. but when
i send data from pic18f458 to 16f876. Pic16f876 receive data ERROR. i dont' know what happen
in my code. because it is a one part of my code.
below is your code

Please explain the PortB values i should update. i'm very confuse about this. because this is a test sourcecode for my work.

Thank you very much.
//====================================================
He could update the PortB values before he reenables the ints



Code:
while(1)
{
send_packet(odata,5);
// Update the PortB values here
enable_interrupts(INT_RB);
}
//====================================================

[Humberto]

[A]

i'm not confuse about rb6 and rb7. i know rb6 is a clock for programming
and rb7 is data for programmin but i must use rb7 like data pin and rb6 like clock for my MCU. because i use pic16f876+24lc64 like smartcard(it'is called Silvercard) and circuit in Smartcard like this picture on below link
i make my board like smartcard and i connect it to lcd and 2 led for debug data when i programm and receive data from terminal (i make terminal and smart card by my self). i'm not sure it is bug in my program or my hardware but when i transfer between pic16f877(Terminal) and pic16f876(smartcard) data transfer is ok but at baud rate 4800 (data is ok)
but i must use pic18f458 instead of pic16f877. because memory in pic16f877 is not enough for my code and when i transfer data to pic18f458. Data transfer from pic18f458 is not receive by pic16f876(Smartcard) and i must connect with pic16f876 at baud rate 9600. because i must follow by ISO7816-3 thank you for your answer. and i will try to solve my problem and please help me or tell me about sourcecode. if you see error in my sourcecode. thank you


http://ucables.com/ref/5SILVCARD/v180,software,download

You will see circuit of smartcard(Silvercard--> PIC16f876+24LC64) at the end of page

Sorry for my english.

[Humberto]

I had been looking the Silvercard schematic.
Why use INT_RB to receive data ? According to your code you have
enough time for polling RB7 using a software uart handler, without
using interrupts.

Just a guide:

[A]

Thank you Humberto. Now my Test program is OK. but now i will try this code for my real program. thank you very much. and if u don't mind. May i contact U by e-mail. My e-mail is [email protected]

[Humberto]